Discovering Essential Plumbing Skills is Essential for Installing a Bathtub
Discovering Essential Plumbing Skills is Essential for Installing a Bathtub
Blog Article
How do you actually feel in regards to How to Install a Bathtub?
Installing a bathtub isn't specifically brain surgery, however it does need strong plumbing, woodworking, and sometimes, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably tough project. If the old tub is conveniently easily accessible, the task can move easily; if you have to open a wall surface to get rid of the old tub as well as place the brand-new bathtub, the task is much harder. In either situation, the task is within a residence handyman's skills, although you will need a helper to move out the old tub and embeded in the brand-new one. Make certain you have certified yourself for the job as well as are comfortable attempting it. Rather than hiring a specialist to take control of a halfway-completed task, it is much better to consider using one before you start. Chances are you may require an expert plumber to make tube links.
This short article will aid you install a new tub in your restroom if you have actually currently acquired a brand-new tub and do not need to alter the arrangement of your previous water supply pipelines.
Your tools as well as product list ought to comprise the following:
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, then the first thing you need to do is disconnect the supply of water. After doing so, turn on the faucets to drain any type of water continuing to be in the system. The process of getting rid of the existing taps can be rather troublesome because of the limited accessibility that is usually the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been removed, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the single taps from transforming during this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and the other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will need lowering couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin making certain that the washing machines are in place between the tap and the sink. Secure the tap in place with the manufacturer provided backnut. Once the tap is securely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal faucet adapters. The former type should be attached to the tap finishes first, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Bathtub
Making use of the two wood boards under its feet, put the bathtub in the called for position. The wood boards are practical in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four little factors.
The next objective is to ensure that the tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the bath tub until the spirit level checks out degree.
To install taps, fit all-time low of the outermost adaptable tap connector to the proper supply pipeline by making a compression sign up with; then do the same for the other tap.
Turn on the water system and also examine all joints and also brand-new pipework for leakages and tighten them if necessary. Fill the bathtub and also examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Lastly, repair the bath paneling as described in the manufacturer's user's manual. Tiling and also sealing around the bathtub should wait till the tub has been used a minimum of when as this will resolve it right into its final placement.
Getting ready for the Installation
First of all, the sustaining framework supplied with the bath must be fitted (if called for) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to make sure that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to stop pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you make use of every one of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final placement.
Tiling Around the Bath tub
In the location where the bath satisfies the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack an inflexible seal, causing the water to pass through the wall in between the bath as well as the tiling, leading to issues with dampness as well as feasible leaks to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components and also fittings. They are offered in tubes as well as cartridges, and also can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water prior to securing, to enable the motion experienced when the tub remains in usage. The sealer can break fairly early if you do not take into account this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise conveniently offered on the market. It is suggested to fit the ceramic tiles using waterproof or waterproof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed reading our article on Installing A Bathtub. Many thanks for spending some time to read our post. So long as you appreciated our blog entry kindly don't forget to share it. I thank you for reading our article about Tools You Need to Install a New Bathtub .
Get Started Report this page